First you will solder in your 15 wires to each nand and 2 wires for external power Here is a closer up image of the one above Be sure to throw some hot glue down to keep your wires in place, and keep them from crossing. Some good electrical tape is also recommended as some of your hot glue may come up eventually due to the intense heat this console puts out. On this model i find this is one of the few orientations i found the infectus will fit without sitting on top of other components (and there is little room under the mobo shielding) Try to keep from crossing wires as little as possible!!! Please take note of where i have ran the wires from the other side as later we will have to dremel out this area on the shielding. Directly under the piece where the antenna gets secured is where we will dremel Both top and bottom of the shielding will have to be cut for wires to pass through. This area has been dremel'd out to allow the usb cable to excape the inside of the shielding.
I have grinded some off of 2 pegs used to align the fan and heatsink, seen top right of photo, they still penetrate the shielding but not far enough to crush the chip placed underneath where they will sit. This area is cut out to allow the passing of wire for external power. To finish my install and give it a more OEM look (and mainly protect wires which otherwise would protrude from the case from out pet) Here you see i have marked the area with a razor which is exposed and usable with the hdd door cover removed. Dry fit after drilling and dremeling the shape of a female mini usb smd connector.
Connection for external power has been added and wired up, nothing can be done now untill the epoxy has set. Here the usb cable is allowed to pass through the shielding It is then ran tightly around the front of the fan. (notice i have removed the rubber off of most of the cable to make it smaller. It is then ran to where it will rest.
May 15, 2007 infectus ps3 nand flasher - how infectus will downgrade ps3 from 1.6 to 1.5 firmware!!! Jun 07, 2013 How to use infectus to read/write ps3 NAND+DOWNGRADING 3.6x and Waninbrick FIX. How to successfully use infectus to read/write ps3 NAND.
Some extra length of cable has been alloted for both the usb and power to ease dissassembly if it should ever be needed. Hot glue has also been applied to keep wires from wiggling lose and shorting themselves. Here is the back of the shielding with the wire going from one side to the other through our dremeled hole. And finally we can begin flashing!!!! With external power and a professional soldering job you can rest assured you will not brick your console.
(please note the arrow pointing to hot glue applied beneath smd mini usb connection to protect it) Please feel free to mimic this install, or if you cannot please contact me to do this for you, or any other console's install, to help me fund another console to run tests on.
InFeCtuS 2 is the first versatile modchip ever released in the market, created to work with many different consoles. InFeCtuS will give you access to so many features that it's impossible to describe them all today, some are still in development and more will come in the future, just stay tuned on www.infectus.biz We developed this modchip with an OPEN concept, we use a CORE reprogrammable, a 512kb flash on board and an USB interface for the PC communication. The hardware has a very HIGH QUALITY component design: * The core of INFECTUS is the new ACTEL ProASIC3 FAMILY, the new family after the famous APA075 used in the past in many PS2 projects.
* We used a 512Kb parallel flash SSTSF040, with a high transfer rate and performance. * Finally, we have got a REAL USB2.0 processor. This high quality component can manage the communication between ACTEL and PC (mini usb connector). * All of the chip PLD/FLASH/USB parts are 100% reprogrammable via USB communication.
* For security reasons, all of the applications stored in the flash are AES 128-bit encrypted, to protect our work against chinese market! * The project is produced in Europe with the last technology of BSDL testing. The new Infectus modchip Being InFeCtuS so versatile, we want to show you at least a little part of its features, ordered by console.
XBOX360 SUPPORT: * X360 CPU TIME ATTACK + DOWNGRADE DASHBOARD (necessary downgrade ADDON) * Allows to gain total access over the XBOX360 flash driver, so that you can read and write the internal flash of any X360 DVD READER in the market. Everything can be managed with a very simple and user friendly PC software.* COMPLETE SUPPORT OF BENQ DRIVERS * FLASH ID realtime patching, your xbox360 cannot understand if there is any flash running other than the original one. * GLOBE MODCHIP 360 100% emulation including ON / OFF LED PS3 SUPPORT: * The first work to be done is to allow our users to flash directly the PS3 BIOS by USB. So no more problem with firmwares, you can install everything you want, when you want. D33011 Ati Drivers. All the complications due to firmware versions that cannot be downgraded will not bother you anymore.
This solution will be released in the next 4 weeks! * Another new feature that we want to add is a REAL TIME patching of the firmware part that you want to be emulated from the chip. Being the 512Kb flash not enough to store a real dual firmware, we'll have to wait for the first hacked firmware to understand if a 'realtime' patching will be possible.
In case we won't be able to find more ideas, a new version of Infectus with a memory expantion bay will be released. PS2 SUPPORT: * Complete O2 MODCHIP emulation 100% with all functionalities (www.o2mod.com) - Included for FREE WII SUPPORT: Of course this is a free 'bonus' in this mod because, we know, most of You wouldn't install such a big and expensive chip on a WII, but being it free. It's a good chance! * WII D2C 13 wire modchip, implemented on INFECTUS the ARGON firmware SOFTWARE MANAGEMENT: The possibility to manage the features using an easy software is one of the BIG advantages of this modchip solution! * WIZARD help for the users: you will simply follow software's instruction step by step, everyone would be able to install and manage the INFECTUS MOD. * When you will be ready to install INFECTUS on a DVD DRIVE 078 XBOX360 FIRMWARE, the software will assist you with a 100% automated extraction of the key and the patch of new firmware.
* WIZARD configuration based on XML for an automatical update of last firmwares. * X360 FIRMWARE checksum, the software will tell you if you are actually using the correct firmware (this feature is only available in WIZARD procedure) * HELP section to allow an easy searching of X360 firmwares.